ELUTRIATION METHODS

 ELUTRIATION METHODS  ::

The size separation of powder is based on the low density of fine particles and high density of the coarse particles Elutriating tank is used to separate the coarse and fine particles of powder after levigation The dry powder or paste made by levigation process is kept in an elutriating tank and mixed with a large quantity of water The solid particles are uniformly distributed in the liquid by stirring and then it is allowed to settle down Depending on the density of solid particles it will either settle down or remain suspended in water The sample is withdrawn at different heights through the outlets These are dried and thus the powder with various size fractions are collected . 


        Nowadays in elutriation process the particles are suspended in a moving fluid generally water or air The apparatus consists of a vertical column with an inlet near the bottom for suspension an outlet at the base for coarse particles and an overflow near the top for fluid and fine particles One column will give single separation into two fractions if more than one fraction is required a number of tubes of increasing area of cross section can be connected in series The velocity of the fluid decreases in succeeding tubes as the area of cross section increases thus giving a number of fractions These fractions are separated and dried 
Advantages of Ehutriation Method 
(1) The process is continuous . 
(2) Depending on the number of fractions required the same number of tubes of different area of cross section can be connected . 
(3) The separation is quick as compare to other methods of separation 
(4) The apparatus is more compact than as that used in sedimentation methods . 
The main disadvantage of this method is that the suspension of solid particles has to be diluted which may not be desired in certain cases . 

TRANSLATE IN HINDI ::

एल्युट्रिएशन के तरीके ::

पाउडर का साइज़ अलग करना, बारीक कणों की कम डेंसिटी और मोटे कणों की ज़्यादा डेंसिटी पर आधारित होता है। लेविगेशन के बाद पाउडर के मोटे और बारीक कणों को अलग करने के लिए एल्युट्रिएटिंग टैंक का इस्तेमाल किया जाता है। लेविगेशन प्रोसेस से बने सूखे पाउडर या पेस्ट को एल्युट्रिएटिंग टैंक में रखा जाता है और बड़ी मात्रा में पानी के साथ मिलाया जाता है। ठोस कणों को हिलाकर लिक्विड में एक जैसा फैला दिया जाता है और फिर उन्हें नीचे बैठने दिया जाता है। ठोस कणों की डेंसिटी के आधार पर वे या तो नीचे बैठ जाएंगे या पानी में सस्पेंड रहेंगे। सैंपल को आउटलेट के ज़रिए अलग-अलग ऊंचाई पर निकाला जाता है। इन्हें सुखाया जाता है


 और इस तरह अलग-अलग साइज़ के हिस्सों वाला पाउडर इकट्ठा किया जाता है। आजकल एल्यूट्रिएशन प्रोसेस में पार्टिकल्स को एक चलते हुए फ्लूइड में सस्पेंड किया जाता है, जो आमतौर पर पानी या हवा होता है। इस उपकरण में एक वर्टिकल कॉलम होता है जिसमें सस्पेंशन के लिए नीचे एक इनलेट, मोटे पार्टिकल्स के लिए बेस पर एक आउटलेट और फ्लूइड और बारीक पार्टिकल्स के लिए ऊपर एक ओवरफ्लो होता है। एक कॉलम दो हिस्सों में सिंगल सेपरेशन देगा। अगर एक से ज़्यादा हिस्सों की ज़रूरत हो, तो बढ़ते क्रॉस सेक्शन एरिया वाली कई ट्यूब्स को सीरीज़ में जोड़ा जा सकता है। क्रॉस सेक्शन एरिया बढ़ने पर बाद की ट्यूब्स में फ्लूइड की वेलोसिटी कम हो जाती है, जिससे कई हिस्से बन जाते हैं। इन हिस्सों को अलग करके सुखाया जाता है।

एल्यूट्रिएशन मेथड के फायदे

(1) यह प्रोसेस लगातार चलता रहता है।
(2) ज़रूरी हिस्सों की संख्या के आधार पर, अलग-अलग क्रॉस सेक्शन एरिया वाली उतनी ही संख्या में ट्यूब्स को जोड़ा जा सकता है।
(3) यह सेपरेशन दूसरे तरीकों के मुकाबले जल्दी होता है।
(4) यह उपकरण सेडिमेंटेशन मेथड में इस्तेमाल होने वाले उपकरण से ज़्यादा कॉम्पैक्ट होता है।
इस मेथड का मुख्य नुकसान यह है कि ठोस पार्टिकल्स के सस्पेंशन को पतला करना पड़ता है, जो कुछ मामलों में ज़रूरी नहीं हो सकता है।

Post a Comment

0 Comments